Відео

😂

😊

Bro that was really useful video thanks a lot 👍🏻 my Mazda start to breath again 😂

thank you 👍

Thanks bro I had a stubborn crate that did not want cooperate. Lol

Ordered the same covers , I'm still awaiting my derby cover and timing cover from Harley when I bought my street bob on the 6th June said I should have them in 10 days.......still waiting

5:54 JK creampie

My dash was cracked in multiple places. All I had to do was rip it off lol. I have a replacement ordered

18:22 Weber didn't drill a hole in the metal base for the plastic bit to sink into. So my door won't hang.

hi man, i saw that you fixd a monitor way before, can you give me some tip on my samsong g5 that keeps torn off almost eavry 10m for like 30sec and back on agien ? i tried a lot of things olrady, I used other cables. display port and HDMI. I used a different power cable. I reset the screen settings and also tested with different heart frequencies and reaction and boost functions, and no defrent best wishes

What can gear did you use ?

Awesome video. Followed your instructions and worked great. That center bolt though. Wow. What an SOB. Thanks again

Get a jaw puller for the rotors.

Works great if you don’t have a car with a lot of power. I did this for about a year and the Velcro started pulling the carpet off the speaker box and eventually it will get to the point where it will rip the carpet off. Use cam buckle lashing straps and go through the hook in the back of the seat. Works much better and it won’t tear anything up. Also much easier to release if you need to get to your spare.

Great video!

Thank you for sharing this! I just made the same installation and thanks to you it was a breeze.

Are you concerned with condensation building up on the back of the display? Think I'm going to put a tall piece of foam on the bottom part of the vent to deflect the air up

Is this the same process in an 99?

Zoinks!.. I thought you said installing a catheter.. 😮 I know, right. (FYI, removal is worse).. 😬

The heads are on the bench. Please stop using that improper spring compressor and use the right tool.

What size TV was that? Does. the rotate work with 75" or 85" as well?

Excellent video. Saved me a lot of $$ and gave me the confidence to do the job myself. Always a little hesitant to undertake a project like this for the first time but your step by step instructions made it easy to understand the process. Thanks!

Couldve ran 1 single power wire to a muliti-fused distribution block for a neater and more efficient install sans goes for the negative wires as well.

what thread sealant are you using? I have heard you just use a dab of RTV

Terrible video !! I definitely won’t be following it 😂

Ghostly, your info and all your videos have set me at ease. One piece of info I haven't been able to find is if my crank bolt needs to be new. I've heard it's torque to yield. Do you know either way. Response would be greatly appreciated

can this engine be installed in a 2016 chevy Silverado? to replace the l86

I keep hearing of "plugged" injectors on the LT1. If you have the injectors out, can you run some cleaner through the injectors to clean them or do they need to be replaced?

Thanks for the tutorial. I have a 2006 Cobalt and tonight was the first time the filter was changed. Prior to this, the AC was bogger down and not very cool. I just tested it after finishing and now the highest setting is actually high.

Can you help me with fixing the DPN ports on the back of the monitor?

Hey there! Are you interested in vehicle lighting stuff sponsor?

I’m curious how it’s holding up

where did you run the power cord?

Thank you brother

I love how EVERYONE'S main concern when installing amp in rear.. 'You can still put groceries in there.' 😂

Useless for explaining how to remove console

Did you have to do a throttle relearn after un plugging the throttle bodies ?

You da man, much appreciated!

Good video

Do you think the pin will be needed for the and older molder Chrysler like 2005

what is the height of the oil filter?

thanks..i dont quite understand the reason for the measurement. it would seem to me that when it goes back in, it will only be able to go at the point where the steering shaft enters it. Then, the 2 large mounting bolts will locate it.. am i wrong? I understand the part that you do not want to turn the steering wheel to avoid breaking the clock spring.

Drink water.

This link no longer works. 😢

Have a 22 street bob and can't fit exhaust my self due to being a UK model it has four O2 senors on it and have to pay shop prices to get it done, slightly pissed at this

Am I missing something? There is no footage actually installing a pulley, only torquing a bolt.

What should it be for optimal bass

Do you think those are louder than stock with Vance Hines slip ons? I have a 2020 Fat Bob. Thinking of going with the sweepers also.

Worst video

Use a pencil magnet to remove and install keepers.